تحليل بسيط لدائرة شاحن صيني يعمل بالتذبذب الذاتي smps 5v 1A.
..........................
تتكون الدارة من قنطرة توحيد، ومكثف تنعيم، وترانزيستور التقطيع الرئيسي واخر يتحكم فية، ومحول فيريت، مقاومة البدء ومكثف ومقاومة، مقاومة تحسس التيار، والجزء الثانوي يتكون من دايود، ومكثف تنعيم، وابتوكبلر، وليد، وزينر.
اولا المكثف والمقاومة التوالي ف المقاومة هنا تتحكم في سرعة شحن وتفريغ المكثف، والمكثف لايمرر التيار المستمر"DC" فقط المتردد"AC" لاكن في بداية الDC المكثف يمرر بلصة/نبضة سريعة.
ثم سنتحدث عن قلب/دائرة التذبذب التي تتكون من مقاومة البدء"start-up" وملف الauxiliary او الفيدباك والمكثف والمقاومة التوالي.
ف عند بداية التشغيل يدخل التيار الي الملف الابتدائي ومقاومة البدء ثم الي قاعدة ترانزيستور التقطيع الرئيسي"Q1" لاكن تيار غير كافي لتشغيلة كاملا يدوب يسمح لتفريغ تيار الملف الابتدائي بالذهاب الي الارضي ثم يعمل ملف الفيدباك ليمرر التيار الي المكثف ويشحنة ثم الي قاعدة الترانزيستور فيكون الQ1 مفتوح كاملا ثم يتم تفريغ المكثف من خلال الترانزيستور"تيار القاعدةB يسرب الي الباعثE..ف الصور ستجد صورة من كتاب مبادئ الترانزيستور توضح ذالك" ف يغلق الترانزيستور وهكذا وتعاد الدورة مرة أخري فيعمل الترانزيستور ويغلق...
ف دائرة التذبذب تعتمد علي مقاومة البدء وملف الفيدباك والمكثف والمقاومة التوالي فيعملان علي تذبذب التغذية على قاعدة الترانزيستور بالتالي فتحة وغلقة فمن الشائع جدا في هذة الدوائر عند رؤية مكثف ومقاومة توالي خارجين من طرف محول يكونو تبع دارة التقطيع لاكن هناك دوائر اخري بها دايود ومكثف وزينر قبل المقاومة والمكثف.
دارة التغذية العكسية لمراقبة جهد وتيار الخرج...
*لو التيار كان كبير سيمر خلال مقاومة تحسس التيار بالتالي سينشأ عليها جهد كبير ذالك سيشغل قاعدة الترانزيستور الثاني بالتالي سوف يقلل"Duty cycle" او سيقطع التغذية عن الترانزيستور الرئيسي.
*لو كان الجهد الخرج زاد او قل الفوتوكبلر سيعمل من خلال تحسس الجهد من خلال الزينر الموصل بة بالتالي سيقلل التغذية من علي قاعدة الترانزيستور التقطيع من خلال تسريع تفريغ مكثف التذبذب او فتح الترانزيستور التاني لإغلاق الاول.
الجزء الثانوي/الخرج... بسيط جدا يتكون من دايود توحيد"وضعة غير تقليدي كما معرفة لاكن عادي لايؤثر علي عملية التوحيد" ومكثف تنعيم، ومقاومة تحديد التيار الي الليد.
عيوب لاحظتها أنة لايوجد فيوز ولا فلتر دخل ولا يوجد دائرة السنابر"snubber circuit" ولايوجد فلتر خرج ولا مكثفات امان"CX,CY" وحتي قيم المكثفات صغيرة لاكن هذا شاحن صيني حتي اتوقع شكل الخرج غير جيد/غير منتظم واقل من واحد امبير،ولا مقاومة حمل ودائرة التذبذب قد تكون غير مستقرة في عملها.
سامحوني اخوتي أن قصرت في الشرح او حصل فية لخبطة لان في بعض النقاط معتمدة علي بعض لو طرحتها الان قد تكون غير مفهومة عند البعض خصوصا في عملية التذبذب...
The circuit consists of a full bridge rectifier, smoothing capacitor, main shredder transistor and another controlling, ferrite transformer, starting resistor, capacitor and resistance, current sensing resistance and the secondary part consists of a diode, smoothing capacitor, an optocoupler, led, and a zener.
First, the capacitor and the resistance respectively The resistance here controls the speed of charge and discharge of the capacitor, and the capacitor does not pass the DC current only AC, but at the beginning of the DC capacitor passes a quick pulse.
Then we will talk about the oscillation circuit.. which consists of start-up resistance, auxiliary/feedback winding, capacitor and resistance respectively.
At the start of the operation enters the current to the primary winding and start-up resistor then to the base of the main transistor"Q1" but not enough current for make full on but allows to discharge the current of the primary winding go to the ground and then the feedback winding working then pass the current to charging the capacitor and then to the base of the transistor now Q1 is fully on then the capacitor is discharged"through the Base to the Emitter of the transistor Q1" and the transistor closes/off and so the cycle is repeated again and the transistor works on and off ...
So the oscillation circuit depends on the start up resistance and the feedback winding and the series capacitor and the resistance, they work on the feeding fluctuation on the base of the transistor to make on and off.
It is very common in these circuits when you see the capacitor and resistance sequence out of the transformer is followed by an oscillating circuit but there are other circuits with a diode, capacitor and Zener before the resistance and capacitor.
Feedback circuit to monitor output voltage and current ...
* If the current was large will pass through the sensing current resistor will arise a large voltage that will turn on the base of the second transistor will reduce the "Duty cycle" or cut off the feed on the main transistor.
* If the output voltage increased or decreasing the optocapler will work by sensing the voltage through the connected zener thus reducing the feed on the base of the main transistor by accelerating the discharge of the oscillation capacitor or open the second transistor to close the first.
Secondary part / output ... Very simple consists of rectifier diode "unconventional mode as we know but it doesn't affect the process of rectifying" and a smoothing capacitor, and resistance to limit the current of the LED.
Noticed disadvantages... there is no fuse and no filter input and there is no snapper network and there is no output filter and no safety capacitors"CX,CY" and even the values of capacitors is small but this is a Chinese charger so I expect the output format is not good / unstable and less than one amp no load resistance and oscillation circuit may be unstable in its operation.
in a previous post i explain how does SMPS, snubber circuit, safety capacitors and some analysis how work in Arabic but don't worry I'll explain upcoming posts in english and for the old posts you can translate it by clicking on autotranslate to your language but try to understand because the literal translation may be strange, and some of the points mentioned have been discussed previously and also other topics i think it's good enough that might benefit you... thanks.